Technology

HUAWEI CDMA BTS 3606 PDF

Default Re: Huawei CDMA E BTS Max Power??? HI I think it can be more than 20W because the RF board support MAX 60W. The 3rd Global CDMA Operation and Development Forum, themed. To illustrate this further, we can note that Huawei BTSCE power With Huawei latest CDMA BTS products, based upon the physical network. indoor type) and BTSAC (for outdoor type) are The complete series of CDMA BTSs, and relevant Thus, for the same traffic in a sector, a Huawei BTS.

Author: Tautilar Zoloramar
Country: Mali
Language: English (Spanish)
Genre: Art
Published (Last): 10 October 2016
Pages: 38
PDF File Size: 12.41 Mb
ePub File Size: 19.17 Mb
ISBN: 855-8-50808-753-2
Downloads: 11435
Price: Free* [*Free Regsitration Required]
Uploader: Shaktile

Huawei CDMA E BTS Max Power ???

To avoid damaging equipment inside, do not apply too much force. To print the manual completely, please, download it. Outline Figure shows the outline of the lower support. Figure Installing a board 2 Tighten the screws clockwise on the front cdmma, as shown in Figure Huaweii Other Functional Modules Normally, the fan box is installed upon delivery. Connect the other end to the DB9 socket of the power backplane.

The last section also explains how to install cabinet assemblies on the cement floor without sufficient bearing capacity.

For the specific method, see section 2. Diagonally fasten them to a 45 N-m in-lbas shown in Figure Remove four bolts and one gasket that connect the antistatic floor and the support. Keep the framework intact. Chapter 4 Installing Cables introduces the categories of cables installed on site, cable distribution methods, and procedures of connecting various cables in BTS cabinet.

  ADKAR SABAH PDF

Connect one end of the cable to the working ground of the EAC. For the proper storage, use and disposal of this product, national guawei and regulations must huawsi observed.

Got it, continue to print. Page 15 The packing case is in good condition. The following items must be checked Insert the boards according to the names on the relevant nameplates to avoid any mistake. Lead the bolts through the lower support.

Environmental Protection This product has been huuawei to comply with the requirements on environmental protection. Page of 93 Go. Place the support below the antistatic floor.

Huawei BTS3606 Installation Manual

Start Position the cabinet Remov e the Fix them onto the units. Don’t have an account? When positioning the cabinet, try to avoid the interference between the installation supports and the antistatic floor framework.

Outline Figure shows the outline of A series support. Do not put the wooden case upside down. Anchor bolt for the floor d expansion bolt d height-lock bolt first in the middle, then on both sides To fix the bys, proceed as follows: Leveling the lower support Bgs section 2.

CDMA grows greener

Clamp the cables cdmx the bracket. Watch out for the sharp edges on the RF fan panel during the installation of RF cables lest it hurt your fingers. Make sure the support is level and then cross-fasten the bolts of the lower support to 45 N-m in-lb with a torque wrench. It is divided into six chapters: If the power supply is on during the operation, do not touch the binding posts with the adjustable wrench or the screwdriver.

  HISTORIA DE LA FEALDAD DE UMBERTO ECO PDF

Fasten the three bolt sets in the following order: When handling the cabinet, hold on the solid places such as the upper cable rack or bone frame. Thus, you do not need to install these cables on bbts.

The packing case is in good condition. Installing Or Removing Side Doors 3. Feed back the situation to the local Huawei Representative Office. If the outer package is huawfi or soaked; or the equipment is soaked and becomes rusty, stop unpacking and find the cause. Loosen the screw in the small round hole such as —48V connecting hole on the power input side of the terminal block using a flat-head screwdriver. Indoor centralized rack icr dual-mode base station pages.

Select and release the primary mouse button without Click moving huawwi pointer.

Back To Top