FIDC tracking water injection system osa User manual v4w Page 2 GETTING TO KNOW THE AQUAMIST HFS-6 osa Aquamist has been. WORKS has been using Aquamist Water Injection since We have seem them all since then and still strongly believe these are the most well thought out. Retired System Information. Below you will find technical info and original sales info for the systems. Aquamist HFS-6 Injection System. Aquamist HFS
|Published (Last):||6 September 2011|
|PDF File Size:||5.36 Mb|
|ePub File Size:||14.92 Mb|
|Price:||Free* [*Free Regsitration Required]|
Jet sizes from 0. The fixed injection rate of the HFS-1 suits this application perfectly, and with the best failsafe system in the industry, is a great aquamistt. Aquamist 2s The 2s is a fully-mappable water-injection system, is pre-pressurizedequipped with diagnostic circuitry, able to detect blocked water-jet and abnormal operation problems.
Back to home page Return to top. Delivery times may vary, especially during peak periods.
A psi Adjustable Pressure Switch normally closed sets the cut-in point relative to the manifold pressure. San Diego, California, United States. With the best failsafe system in the industry, and a standard 13ohm injector that could be be driven by a spare PWM channel from your EMS, the HFS-5 easily integrates into nearly any application.
An additional pair of wires supplies a stablised output voltage of 5 volts for driving a MAP manifold absolute pressure sensor. In hard water areas, clean the filter in a small glass of diluted household lime-remover occasionally. Back to home page. For those who want a 3-D water injection MAP but do not want to spend the time-consuming task of mapping, this system is perfect for you.
Thread size of the jet is M8x0. As usual, except for the water tank, the system is supplied with everything needed to be fitted with ease.
MF2 MF2 is the brain of the system, ultimately responsible for the vital functions of metering the water delivery rate. The similarity ends when the manual pump actions is replaced by electro-magnetic fields and speed is also cranked up to about 50 strokes a second! Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.
The color supplied with the kit is semi-translucent white, but red, yellow, green, blue and black are available on request. Estimated on or before Mon. Its primary function was to regulate the water pressure during injection and idle periods set at 5 bars. Add to watch list Add to wish list. In addition, high speed drive motor tends to suffer from burn-out under prolonged continuous running.
In addition, it has diagnostic circuitry designed to detect blocked water-jets and cut pipes. Developed with years of experience in World Rally Championship racing and feedback from the industry by the most demanding users, the HFS-6 surpasses all other systems in operation, performance, and reliability.
It is normally fitted to the vacuum side of the inlet manifold 2D mode for applications where load signal throttle angle sensor or manifold absolute pressure sensor MAP sensor is available.
The water-pump is activated when an adjustable pressure switch, fitted to the inlet manifold, reaches its preset point: The system provides a pre-pressurized water line up to 8 bars and the flow rate is metered by our latest High speed Valve HSV. This inline valve is made of high grade stainless steel. Start of add to list layer.
Retired System Information
Water travels through these grooves, acquiring a swirling motion before leaving the small hole on the tip: A high pressure pump with NO mechanical links, thus eliminated damages caused by jamming.
Sell one like this. Seller assumes all responsibility for this listing. Water aquamisf then delivered without being in contact with the drive-motor, pressure and delivery rate is regulated by internal high-tech electronic circuitry.
A pre-pressurized system enables instant response on demand. Peak pressure can go as high as psi! The inline valve is made of high grade stainless steel and capable of achieving a cycling rate of over Hz.
See full item description. There are no mechanical links between the piston and the drive motor: Skip to main content.
After several signal conditioning stages it finally arrives at the pulse-width-modulator stage, and the output signal is then converted into digital pulses before being sent to the electro-magnetic water valve. Aquamist 2c The 2c is designed for stand-alone EMS systems. For applications where load signal throttle angle sensor or manifold absolute pressure sensor MAP sensor are available, the MF2 can read these signals and perfom 3-D mapping functions.
For additional information, see the Global Shipping Hgs-6 terms and conditions – opens in a new window or tab.
As the pulsed signal from the pressure switch is directly proportional to the flow of water, it can either be recorded by an on-board data acquistion system for diagnostic purposes or read by the control ECU to monitor blockage or water jet and other faults that may arise. Aquamist 1s The 1s is a single stage system that consists of an ERL high-pressure electro-magnetic water pump, adjustable pressure switch, plus all the necessary yfs-6 to form the basis of a starter kit.
The ERL electro-magnetic pump In order to find a pump that will reliably perform under the harsh environment of aqyamist engine bay, we have no alternatives but to design our own. Of course a pressure of at least 3 bar is required.